Recessed, chandelier, outdoor, and smart lighting installation across Beverly Hills. CG's Electrical Services handles lighting projects in one visit, done right.
We did a kitchen lighting project last spring that's stuck with us. The homeowner had been living in the house for eleven years. Every night for eleven years, she had cooked dinner under two undersized ceiling fixtures from the original 1990s build that left the entire counter run in shadow. She had renovated the kitchen seven years earlier and kept the original lighting because the renovation budget had run out. She'd been telling herself for the seven years since that the lighting was "fine" because she'd gotten used to it.
We did the walkthrough. Eight slim LED downlights, two pendants over the island, three under-cabinet LED strip runs, and an LED-compatible dimmer to replace the old incandescent dimmer that had been making the original fixtures hum at low settings. One day on-site. The kitchen went from a dim cave to a fully lit working space. She texted us the next week asking when we could come do the basement.
That's the part we want to address head-on. Lighting projects sit on lists for years because the planning feels bigger than the actual install. The walkthrough is twenty minutes. The fixture conversation is another ten. The install — for most rooms — is a single day. Whatever has been frustrating you about your lighting is almost certainly fixable on a faster timeline than you've been telling yourself.
From a single fixture swap to a full commercial LED retrofit — we do it all, in one visit, done right.
Recessed lighting transforms a kitchen, finished basement, or primary bathroom faster than almost any other electrical upgrade. We do new-construction can installs in framed ceilings and retrofit installs in existing drywall, with patch work that minimizes the followup drywall visit. Fixture types we install regularly across Beverly Hills, FL: traditional recessed cans, slim-profile LED downlights for low-clearance ceilings, gimbal trims for art lighting, and wet-location units for showers. Spacing follows the fixture's beam angle and the ceiling height — not "evenly spaced looks nice." That distinction is the difference between a room that lights correctly and a room with bright zones and dark zones.
Your fixture's already on its way. You need someone to mount it without dropping it on the dining table. We handle the part most installers gloss over — weight verification (fixtures over 35 pounds need joist-cavity support brackets that builder-grade ceiling boxes don't provide), dimmer compatibility checks, electrical box reinforcement when the existing box isn't rated for the fixture's weight, and the precise centering that turns a fixture install into a finished room. Two-story foyer installations get the lift equipment, not folding ladders.
Outdoor lighting is where short-term cost-cutting produces the longest-term regret. Builder-grade landscape kits fail in two seasons. DIY installs run undersized transformers that burn out by summer. Cheap fixtures pit and corrode in Beverly Hills winters. We install systems that survive — properly sized transformers matched to total fixture load, fixtures rated for actual outdoor service life, photocell and timer setup that doesn't require manual seasonal adjustment, and underground wire runs at proper depth so the next round of landscaping doesn't expose the cable.
The detail that separates a good kitchen from a great one. Hardwired LED strip lighting under upper cabinets, switched at a location that makes practical sense — not buried behind small appliances. Vanity task lighting that doesn't backlight you in the bathroom mirror. Workshop bench lighting that puts the illumination where the work is. Hardwired installs are cleaner and more reliable than the plug-in puck lights that come loose every few months.
Office spaces, retail floors, restaurants, and warehouses across Beverly Hills, FL. Commercial electrician work covers high-bay LED retrofits in warehouse environments, office grid lighting upgrades that improve daylight quality and reduce energy costs, exterior building lighting and parking lot fixtures, and emergency lighting that satisfies code inspection. Scheduled around your operating hours so the work doesn't interrupt the work.
Lutron Caseta, Leviton Decora Smart, Philips Hue with hardwired dimmer integration, voice-controlled scene setup through Alexa, Google Home, and HomeKit. We handle the install, the network configuration, and the user walkthrough so the system actually gets used after we leave. The most common smart lighting failure isn't installation — it's the homeowner abandoning the system because nobody walked them through how to operate it. We don't leave the property until you can run it.
Flickering lights. Lights that hum at low dim settings. Lights that won't turn off. Lights that worked yesterday and don't today. The fix is usually faster than the diagnosis — a failing dimmer, a backstabbed switch wire, a worn socket, a transformer at end-of-life. We diagnose first, repair second, and don't pad the bill with parts that don't need replacing.
Here's the honest pricing structure. Skip the guesswork.
A straight fixture swap — old fixture out, new fixture in, same junction box — is the simplest job in lighting. Flat-rate per fixture, with the price scaling down for batched fixtures done in the same visit.
Recessed lighting retrofits price per fixture, with the per-unit cost dropping noticeably as the count goes up. The first can in a ceiling carries the diagnostic and wire-fishing labor; the next several cans on the same circuit are much faster.
New circuits drive the price up the most. If a new lighting installation in Beverly Hills needs a brand-new run from the panel, the wiring labor outweighs the fixture work. We tell you which scenario you're in before quoting.
Commercial pricing runs on a project basis with a written scope, because commercial jobs in Beverly Hills, FL rarely fit a flat-rate model cleanly. We walk the space, build the scope, and price it transparently.
Our trucks roll out to lighting jobs fully stocked — the truck inventory is the reason most lighting installations in Beverly Hills don't require a second visit. We arrive prepared to finish.
Plate scanners for identifying joist locations through finished ceilings.
Hole saws sized for every common can fixture trim.
Dust-collection attachments that keep ceiling cuts clean.
Voltage testers and circuit tracers for diagnostic work.
Ladders and lift equipment rated for two-story foyer installs.
Full inventory of LED-compatible dimmers from Lutron, Leviton, and similar brands.
Matching color-temperature LED bulbs in multiple ranges for consistent color across all fixtures.
Lighting projects fall into three scheduling buckets, and each one moves on a different timeline.
Typically get same-day or next-morning windows depending on call timing. Most Beverly Hills, FL homeowners booking a single-fixture swap before noon receive a same-day appointment.
Recessed lighting installs and room-scale relights schedule about a week out, primarily because we want the customer's fixtures confirmed in-hand before the install date. Showing up to a project where the fixtures haven't arrived yet is one of the few wasted-day scenarios in lighting work. We avoid it.
Schedule based on access — many commercial installs in Beverly Hills run after-hours or on weekends to avoid disrupting business operations. Lead time varies with project scale; most commercial jobs schedule within two to three weeks.
Four mistakes that turn a smooth lighting upgrade into a headache. Skip these and you'll be glad you did.
The chandelier that looks gorgeous in the showroom is too big for your dining room. The pendant rated for 8-foot ceilings looks lost at 12 feet. Measure first. Fixture second. Your installer can usually save you a return trip if you call before you buy.
LED fixtures are picky. The dimmer rated for incandescent bulbs that's been in your wall since 1999 will make new LEDs flicker, hum, or refuse to dim past 30 percent. New LED installations in Beverly Hills, FL homes need LED-compatible dimmers. The dimmer is a small line item that fixes a much bigger problem.
Homeowners consistently underestimate how many recessed lights a room actually needs. Most kitchens need more than people guess, especially with darker cabinets and white quartz counters that reflect light back at unflattering angles. Add the cans during the install, not later — the second-visit return trip costs more than the extra fixtures would have.
Recessed lights spaced wrong leave the room with bright zones and dark zones. The right spacing follows the fixture's beam angle and the ceiling height, not "evenly spaced looks even." A fifteen-minute layout conversation with a real electrician saves you from a ceiling that's been done wrong but is now drywalled in.
Common questions about lighting installation and repair in Beverly Hills, FL — answered straight.
A starting rule for a Beverly Hills kitchen is one 4-inch LED can per 16 to 20 square feet of ceiling, adjusted up for darker cabinets and down for lighter rooms. The exact count gets locked in during the walkthrough.
Yes. Old fixtures get removed, packed, and disposed of as part of the install. If the fixture has resale or sentimental value, we leave it with you instead.
Sometimes. If the existing dimmer is rated for LED loads and matches the new fixture's dimming protocol, we keep it. If it isn't, we replace it. We tell you upfront in Beverly Hills, FL which scenario applies.
Yes, weather permitting. Cold-weather installs in Beverly Hills are standard for soffit lighting, exterior wall fixtures, and switch-controlled outdoor circuits. Underground low-voltage runs typically wait for ground thaw.
Most chandelier installations in Beverly Hills, FL schedule within a week of the walkthrough. If the fixture is over 50 pounds or the ceiling is over 12 feet, we may schedule with a second technician, which can extend lead time by a few days.
We're scheduling lighting projects across Beverly Hills for the next two weeks, and the early slots fill first. If you've been sitting on a fixture upgrade, a recessed install, or a flicker problem that's been driving you up the wall for months, this week is the right time to call. The longer the project sits on your list, the longer it stays there. Get it on our calendar and off yours.
Click Here to Call (888) 355-9624